Page 25 of 123 FirstFirst ... 151617181920212223242526272829303132333435 ... LastLast
Threads 481 to 500 of 2452

Forum: The Frame Forum@VSalon

Sage advice and opinions from experienced tradespeople.

  1. Optimum dropout for Belt Drive

    Started by jaybeeboston, 04-17-2017
    belt, belt drive, drive, dropouts, good
    • Replies: 8
    • Views: 3,244
    Rody
    04-20-2017 Go to last post

  2. Advice and experience building your own alignment table

    Started by Weldingfellow, 04-12-2017
    advice, alignment, holes, table, wide
    • Replies: 6
    • Views: 2,720
    Weldingfellow
    04-13-2017 Go to last post

  3. Columbus Max Tubing

    Started by SaltAirCX, 04-06-2017
    columbus, columbus max, max, pipes, set
    • Replies: 3
    • Views: 2,501
    Pi Guy
    04-07-2017 Go to last post

  4. Thick wall tubes?

    Started by JGabriel, 04-03-2017
    frame, frames, oversized, touring, tubes
    • Replies: 3
    • Views: 2,501
    JGabriel
    04-04-2017 Go to last post

  5. Flat mount disc brakes and single speed

    Started by hurricanejosh, 03-16-2017
    brakes, disc, flat, mount, vertical
    • Replies: 10
    • Views: 4,136
    Ben Hudson
    04-01-2017 Go to last post

  6. Hooded sliding dropouts and fillet brazing

    Started by Furry, 03-21-2017
    fillet, fillet brazing, frame, hooded, hooded dropout 1 Attachment(s)
    • Replies: 3
    • Views: 3,471
    progetto
    03-30-2017 Go to last post

  7. Framebuilder Flow Chart and their Beginnings

    Started by Andrew R Stewart, 03-25-2017
    beginnings, builders, nodes, remember, thread
    • Replies: 5
    • Views: 4,007
    fortyfour
    03-26-2017 Go to last post

  8. Tin-Silver for stainless dropouts

    Started by Koldun, 03-21-2017
    alloy, s45, stainless, strong, tin-silver
    • Replies: 0
    • Views: 1,853
    Koldun
    03-21-2017 Go to last post

  9. A report on using a BernzOmatic mapp/oxygen unit for brazing a lug

    Started by Doug Fattic, 03-09-2017
    flame, lug, make, oxygen, unit
    • Replies: 2
    • Views: 2,913
    Ben Hudson
    03-17-2017 Go to last post

  10. Ye ol' chop and slot~~

    Started by drietz, 03-06-2017
    question, seat, top, tube, weld
    • Replies: 6
    • Views: 3,839
    drietz
    03-11-2017 Go to last post

  11. Installing bridges and effect on rear dropout width

    Started by Paul Jacobs, 02-25-2017
    bridge, dropout, frame, latest, rear 2 Attachment(s)
    • Replies: 14
    • Views: 5,625
    crumpton
    03-01-2017 Go to last post

  12. Practice Tubing for Miters, Tig and pretend Lugs

    Started by classtimesailer, 02-21-2017
    lugs, play, practice, tig, welding
    • Replies: 1
    • Views: 2,860
    Eric Estlund
    02-25-2017 Go to last post

  13. Rust Under Powder Coat

    Started by Clockwork, 11-06-2016
    coat, corrosion, powder, rich, type
    • Replies: 19
    • Views: 14,353
    mahall
    02-15-2017 Go to last post

  14. Solvent help

    Started by Andrew R Stewart, 01-05-2017
    caps, drums, end, residue, thoughts 4 Attachment(s)
    • Replies: 10
    • Views: 3,384
    Peter Polack
    02-13-2017 Go to last post

  15. Drainage holes?

    Started by WheelNut, 02-08-2017
    drainage, hole, seat, top, tube 3 Attachment(s)
    • Replies: 18
    • Views: 4,691
    Paul Jacobs
    02-13-2017 Go to last post

  16. The importance of frame stiffness.

    Started by waterlaz, 01-25-2017
    2 Pages •
    1 2
    frame, googling, stiff, subject, tube 1 Attachment(s)
    • Replies: 25
    • Views: 9,163
    progetto
    01-30-2017 Go to last post

  17. Used Oxy-Acetylene Set

    Started by classtimesailer, 01-28-2017
    certification, j28, kit, tank, used brazing equipment
    • Replies: 5
    • Views: 2,677
    Andrew R Stewart
    01-29-2017 Go to last post

  18. Annular Cutter

    Started by macky, 01-12-2017
    annular, cutters, interesting, option, recommendation
    • Replies: 3
    • Views: 3,017
    macky
    01-18-2017 Go to last post

  19. Dillon MKIII

    Started by Adam Leddin, 01-08-2017
    building, dillon, frame, mkiii, torch
    • Replies: 2
    • Views: 3,791
    Adam Leddin
    01-15-2017 Go to last post

  20. Track Forks & Round Blades

    Started by Michael Gordon, 01-14-2017
    blades, purpose, round, track, tradition
    • Replies: 3
    • Views: 2,437
    Eric Estlund
    01-14-2017 Go to last post
Page 25 of 123 FirstFirst ... 151617181920212223242526272829303132333435 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 100 replies or 200 views
Hot thread with unread posts
More than 100 replies or 200 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules