Dear Guest, Please register or login. Content don't create itself! Thank you

User Tag List

Page 5 of 15 FirstFirst 1234567891011121314 ... LastLast
Results 81 to 100 of 288

Thread: Lyrebird Cycles

  1. #81
    Join Date
    Aug 2011
    Location
    Beechworth, VIC
    Posts
    2,536
    Post Thanks / Like
    Mentioned
    10 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Lyrebird Cycles

    Still making main tubes, time for the lateral strips:


    Lateral strips

    The strips are Victorian mountain ash (Eucalyptus regnans), the world's tallest hardwood.


    Laterals wrapped

    All shrinkwrapped up and ready for the oven.
    Mark Kelly

  2. #82
    Join Date
    Apr 2011
    Location
    Sydney, Australia
    Posts
    5,287
    Post Thanks / Like
    Mentioned
    8 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Lyrebird Cycles

    Loving seeing your process afresh, Mark.

  3. #83
    Join Date
    Aug 2011
    Location
    Beechworth, VIC
    Posts
    2,536
    Post Thanks / Like
    Mentioned
    10 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Lyrebird Cycles

    Thanks Rich.

    I'm including a lot of detail as I have made a couple of changes to the process. One which I forgot to flag last week concerns the way the filament winder is used, I'll call it out when the 2nd wind is done on these tubes.
    Mark Kelly

  4. #84
    Join Date
    Sep 2012
    Posts
    1,230
    Post Thanks / Like
    Mentioned
    8 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Lyrebird Cycles

    Quote Originally Posted by RichTheRoadie View Post
    Loving seeing your process afresh, Mark.
    I just love seeing the process!

  5. #85
    Join Date
    Aug 2011
    Location
    Beechworth, VIC
    Posts
    2,536
    Post Thanks / Like
    Mentioned
    10 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Lyrebird Cycles


    Boron

    The strange looking semi-metallic sheen is due to a strange semi-metal: boron.

    From bottom to top: base tube, boron laterals, shrinkwrapped ready for oven.

    Boron is incredibly strong in compression because it is far more resistant to buckling than carbon. This same property means it will not conform to an uneven surface, thus explaining the fuss earlier about making sure everything is flat and even.

    Oh, the peg stops the tube rolling, nothing more.
    Mark Kelly

  6. #86
    Join Date
    Aug 2011
    Location
    Beechworth, VIC
    Posts
    2,536
    Post Thanks / Like
    Mentioned
    10 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Lyrebird Cycles

    2nd filament wind, this one using Hexcel IM10, the highest strength fibre commercially available.


    IM10

    I promised I'd talk about some of the small changes in technique. Several of them are to do with keeping the interface between layers as flat as practicable, mostly by grinding off any unevenness: you can see in the next pic that the slight excess of epoxy left by the shrinkwrapping process on the surface of the boron fibre has been ground flat:


    Winding_Layer_2

    On the boron layers this is incredibly easy: boron lies dead flat and the fibre is harder than the abrasive grit on the grinder so I simply grind until the abrasive starts to slip.

    On carbon it is a lot more difficult: the carbon layers are never perfectly even and carbon is relatively easy to cut. The solution I've developed is to wind the filament at a pitch about 15% shorter than full coverage would require, then grinding until the surface is even.

    For this to work I have to compress the carbon wind as consistently as possible and I found that shrink wrapping, although it works perfectly well for the more rigid materials such as the wood laminae and the boron, doesn't cut it for carbon.

    Since the compression is basically radial, I changed to using 6 reels of 0.3mm fishing line and tensioning by hand (you can't see the hand because it's taking the pic). Note how the bound part (to the left) makes the winding pattern more evident.


    Binding

    This leaves a carbon surface and tiny epoxy ridges which are easily knocked off by scraping back with a hard edge. I then grind down by about 10% of the laminar thickness and end up with a very even flat surface onto which to bond the next layer.
    Mark Kelly

  7. #87
    Join Date
    Aug 2011
    Location
    Beechworth, VIC
    Posts
    2,536
    Post Thanks / Like
    Mentioned
    10 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Lyrebird Cycles

    Time to check that everything is about right:


    First fitup

    The reason for the bits of purple tape will become obvious later.

    BTW that headtube is just a placeholder, I had to start on another one as I cocked up the headset interface on that one.


    Headtube 1
    Mark Kelly

  8. #88
    Join Date
    Aug 2011
    Location
    Beechworth, VIC
    Posts
    2,536
    Post Thanks / Like
    Mentioned
    10 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Lyrebird Cycles

    Selection of leaves for outer layers:


    Leaves
    Mark Kelly

  9. #89
    Join Date
    Aug 2011
    Location
    Beechworth, VIC
    Posts
    2,536
    Post Thanks / Like
    Mentioned
    10 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Lyrebird Cycles

    New process for making the cores for the chainstays, forced upon me because the previous methods wouldn't cope with the bends and angles involved.

    I tried to do it with my 3D printer but I couldn't generate an acceptable result. It occurred to me whilst watching one of the failed attempts that the machine prints in layers of 0.3mm and the wood laminae are only 0.6mm, so with a bit of application I could become the human 3D printer:



    Human 3D_1

    First, cut all the strips. The doubles are to accommodate internal cable routing


    Human 3D_2

    Stack the strips on top of one another, bond them together, rerout the internal channel then line it with epoxy / glass for waterproofing: moisture ingress is the #1 enemy of wood cored carbon structures.


    Human 3D_3

    Bond the clamshells together, making sure the routing is not obscured.


    Human 3D_4

    Bulk out with end grain balsa


    Human 3D_5

    The final result will require some filleting and sealant on the end grain balsa then it will be ready to wrap
    Mark Kelly

  10. #90
    Join Date
    Aug 2011
    Location
    Beechworth, VIC
    Posts
    2,536
    Post Thanks / Like
    Mentioned
    10 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Lyrebird Cycles

    Meanwhile the main tubes are mitred before bonding, reasons will become obvious later.


    Head tube mitres

    The green tape is proxy for a 0.1mm epoxy bondline
    Mark Kelly

  11. #91
    Join Date
    Sep 2012
    Posts
    1,230
    Post Thanks / Like
    Mentioned
    8 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Lyrebird Cycles

    Funny, i would have bet good money that you “finalised” the tubes with the timber leaves before bonding them. That’s me wrong then.

    I’m very curious to see what happens next!
    Colin Mclelland

  12. #92
    Join Date
    Aug 2011
    Location
    Beechworth, VIC
    Posts
    2,536
    Post Thanks / Like
    Mentioned
    10 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Lyrebird Cycles

    Yes I (mostly) do.

    My comment about mitring before bonding was badly written, the mitring is done well before the bonding takes place. I need the mitres within 1mm of where they will eventually be so that the ends of the external leaves can be correctly placed and by the time I get them that close it is easier to just finish the job.

    I placed the first leaves today, a pic tomorrow will make some of this clearer.
    Mark Kelly

  13. #93
    Join Date
    Aug 2011
    Location
    Beechworth, VIC
    Posts
    2,536
    Post Thanks / Like
    Mentioned
    10 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Lyrebird Cycles


    penultimate layer

    Next to last layer on the main tubes.


    Mould_1

    3D printed mould for the BB shell half lug. Yes, it cracked the bed plate when cooling: I can’t seem to win a trick with this 3D printer.


    Bugger

    The end result :


    BB_shell_1

    These things took a good three days to make: there are over 100 individually cut pieces of carbon prepreg in them.

    Logically, the shaped ends on the wooden layers on the tubes fit to the points on the lugs which explains the fuss over getting the mitres right before finishing the tubes.
    Mark Kelly

  14. #94
    Join Date
    Aug 2011
    Location
    Beechworth, VIC
    Posts
    2,536
    Post Thanks / Like
    Mentioned
    10 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Lyrebird Cycles

    I realised once I'd unmoulded these that I've created a lovely stress riser at the bottom of the vee on the lateral sides of the tubes.

    Time to start again.
    Mark Kelly

  15. #95
    Join Date
    Aug 2011
    Location
    Beechworth, VIC
    Posts
    2,536
    Post Thanks / Like
    Mentioned
    10 Post(s)
    Tagged
    0 Thread(s)

    Default Finishing touches


    Sandpaper

    I use a LOT of sandpaper at this stage.


    Tung_Euky
    The magic formula: in the flesh the trasnformation really is magic. Unfortunately my woeful pics don't do it justice.


    lustre

    You can kind of see the lusre of the myrtle beech here, in the right light is just glows.
    Mark Kelly

  16. #96
    Join Date
    Aug 2011
    Location
    Beechworth, VIC
    Posts
    2,536
    Post Thanks / Like
    Mentioned
    10 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Finishing touches

    Transformation,

    Lustre

    it, not is.

    I can spell, really.
    Mark Kelly

  17. #97
    Join Date
    Aug 2013
    Location
    Sunshine Coast BC, Canada
    Posts
    6
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Lyrebird Cycles

    Those glass plates are fragile, and tend to break when they are too slim.
    If you can fit it, go get a borosilicate plate 1/4" thick and avoid the pain. You can get a piece custom cut at a glass place. Ask for the same glass they'd use on a fireplace. Honestly, at 100C, you probably won't break a soda glass sheet either, so check the price and choose whichever makes sense.

    Also, I like to use hair-spray on the plate to ensure better adhesion. I think it also limits maximum plate adhesion because I haven't broken one in a LONG time. Try Aquanet Extra Super Hold, or anything with an acrylate copolymer if you can't find that one.

    Oh, and the lugs look awesome.

    Derek Anderson
    Army Of Evil Robots – Home Pub Furnishings

  18. #98
    Join Date
    Aug 2011
    Location
    Beechworth, VIC
    Posts
    2,536
    Post Thanks / Like
    Mentioned
    10 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Lyrebird Cycles

    Thanks for the tips. The glass bed has a flexible heater attached to it, the manufacturer sells them as a pair and sees fit to charge $150 for a $5 piece of glass with a $10 heater attached to it.

    If I replace it again I will try your method.

    I have solved most of my problems by using kapton tape on the bed and laying the adhesive on it but I will try the hair spray trick.

    BTW I love your stuff, whereabouts on the Sunshine Coast are you? My mother lives in Mapleton.



    If I may return the favour, most of your problems with epoxy seem to stem from using ambient cure with no vacuum.

    Your life will get much easier if you build yourself a temperature controlled box and invest in a vacuum pot. Use a slow cure clear epoxy like ATL R246 ( based on the Gold Coast) with one of their slower hardeners (I can't remember the numbers as I use the fastest hardener as it gives the highest Tg). Mix it well and place it in the vacuum pot and pull it down to full vacuum for 10 minutes. Make up the workpieces and place them in the oven to cure at a profile that suits the epoxy (it will be called out in ATL's data sheet).


    Also if you need surface treatment don't sand, scrape. A brand new Stanley knife blade works a treat. Once you have the surface dead flat recoat it with Northane 2 pack polyurethane clear gloss, should be available at your local boat repair place. The Northane can also be scraped flat but make sure it is totally cured first.
    Mark Kelly

  19. #99
    Join Date
    Sep 2012
    Posts
    1,230
    Post Thanks / Like
    Mentioned
    8 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Finishing touches

    Quote Originally Posted by Mark Kelly View Post
    Transformation,

    Lustre

    it, not is.

    I can spell, really.
    For some reason I didn't notice any of those...

    I can read, really.
    Colin Mclelland

  20. #100
    Join Date
    Aug 2013
    Location
    Sunshine Coast BC, Canada
    Posts
    6
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Lyrebird Cycles

    Quote Originally Posted by Mark Kelly View Post
    Thanks for the tips. The glass bed has a flexible heater attached to it, the manufacturer sells them as a pair and sees fit to charge $150 for a $5 piece of glass with a $10 heater attached to it.

    If I replace it again I will try your method.

    I have solved most of my problems by using kapton tape on the bed and laying the adhesive on it but I will try the hair spray trick.
    ^ That all works too. If you do want to replace that glass, you can usually get those flexible heater sheets on aliexpress for nearly nothing if you want to try home-building it, example: 24V 25mm 2W Square kapton film flexible heater-in Motor Driver from Home Improvement on Aliexpress.com | Alibaba Group , but it might mess with the PID tune for the printer. If the wattage and voltage match, you're probably golden, and there are lots of other elements on that site (click on heater pad on the left side of the listing).

    Quote Originally Posted by Mark Kelly View Post
    BTW I love your stuff, whereabouts on the Sunshine Coast are you? My mother lives in Mapleton.
    Thanks. Other Sunshine Coast though; we're on the less known one west of Vancouver. Great mountain biking (google the coastal crew).



    Quote Originally Posted by Mark Kelly View Post
    If I may return the favour, most of your problems with epoxy seem to stem from using ambient cure with no vacuum.

    Your life will get much easier if you build yourself a temperature controlled box and invest in a vacuum pot. Use a slow cure clear epoxy like ATL R246 ( based on the Gold Coast) with one of their slower hardeners (I can't remember the numbers as I use the fastest hardener as it gives the highest Tg). Mix it well and place it in the vacuum pot and pull it down to full vacuum for 10 minutes. Make up the workpieces and place them in the oven to cure at a profile that suits the epoxy (it will be called out in ATL's data sheet).
    Ha; just built one this summer. Monster 250 litre chamber that can fit several bar-stool tops. Although it turns out that the wood outgasses badly, even if you seal it in advance :O Still works for de-gassing the epoxy just fine. I'll take a look at that epoxy you recommend though... We're using some furniture specific stuff, but it's open time is only 30 minutes, and it's also VERY sensitive to temperature (22C +- 3 degrees ambient, or it hazes like crazy).


    Quote Originally Posted by Mark Kelly View Post
    Also if you need surface treatment don't sand, scrape. A brand new Stanley knife blade works a treat. Once you have the surface dead flat recoat it with Northane 2 pack polyurethane clear gloss, should be available at your local boat repair place. The Northane can also be scraped flat but make sure it is totally cured first.
    Hmmm. How nasty toxic is that stuff? I have been leery of a lot of the better polyurethanes because they have terrifying MSDS docs. I would love to find a decent urethane that doesn't sound like it'll melt my eyeballs and give me cancer in one go. Agreed on the scraping. That's my go-to for tricky wood surfaces too, and we have a broad selection of scraping tools/planes.

Similar Threads

  1. Boedie Cycles
    By Boedie in forum Smoked Out
    Replies: 30
    Last Post: 11-22-2014, 05:45 PM
  2. Magnolia Cycles
    By magnoliacycles in forum Smoked Out
    Replies: 25
    Last Post: 04-11-2011, 04:57 PM

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •