Friday PicFest No.111

[zank]

little...









big...

[Dave Kirk]

A straight up road race bike in progress -

dave

[steve garro]

It's been a busy, busy week. Finally getting my flow back from surgery, an Mtb to VA, tall gal bike for AZ & the "Stuart" almost done - Garro.

[EnginCycles]

Been a while for me. It is bring your son to work day so here is a photo of my super amazing son Jack this morning:


Working on a 953 mtb so here are some lug shots:













Cheers,
Drew

[VertigoCycles]

I could post the standard weld shots but they all bleed together sometimes no? How about something NBR?


Ti damper pin by VertigoCycles, on Flickr

[YiPsan]

A fork for september:

[IMG]
FILE0006 by YiPsan bicycles, on Flickr[/IMG]
[IMG]
04/28/2011 by YiPsan bicycles, on Flickr[/IMG]
[IMG]
04/28/2011 by YiPsan bicycles, on Flickr[/IMG]

and a bike ride:
[IMG]
04/27/2011 by YiPsan bicycles, on Flickr[/IMG]

[Dazza]

Just the usual here
but best viewing results are listen to
a Custodian build under way
but the new website via Ginger's skills and toil is getting closer to release

[Archibald]

Puzzle pieces...


What it looks like assembled:





There are 100's of them....

[Craig Ryan]

Jake Brake just out from paint. Got a peek of some rare sunshine, but hardly enough to show the pearl.

IMG_8276.jpg

Attachment 31660

IMG_8279.jpg

IMG_8282.jpg

IMG_8286.jpg

Attachment 31665

[anthonymaietta]

Justin's Fixed Gear:


Jason's S&S Fixed Gear (to be sanded and final-cleared):






Kevin's Dirt Road Frame (to be sanded and final-cleared):

[Tyler Evans]

It's like Friday Night Lights, just every day: Pure Visual Stimulation.

Crema-ti-9.JPG

Crema-ti-7.jpg

Crema-ti-4.JPG

[bellman]

This week is a CCX/ rain bike ready to deliver and a x-tra large 29 almost ready for paint.

[conorb]

Conor

[tmarsh]

post sandblast, pre-paint...







... tim

[MikeB]

Nearing completion on this small CX frame:


One of these went to paint, and should finishe the other two this weekend:


Welds:


Awesome work this week gents!

[Eric Estlund]

Here are a few- as voted on by Flickr page views:

A new stem hanger for Jame's. This is going on his Kirk, and I wanted something that reflected the rear stop Dave does:




Bernardo's bike gets a rear end:




More back end work, then another stem for Roland.

[e-RICHIE]

basso profundo atmo -

[Tom Kellogg]

Busy:

FNL16c.jpg FNL16d.jpg

Paint prep room on Monday
FNL16a.jpg FNL16b.jpg

Doug's
FNL16l.jpg FNL16k.jpg

Carla's
FNL16j.jpg FNL16i.jpg

Judi's
FNL16h.jpg FNL16g.jpg

Heather's
FNL16f.jpg FNL16e.jpg

[suspectdevice]

An absolutely overwhelming amount of bikes are being made right now.
I had to start riding bikes again just to deal with the stress...

You're looking at all of the 575mm toptube Skeletors that are currently in production

Revised 28mm clearance chainstays.


We use this setup to double-check the numbers on pilot runs(notice the single tacks).


Frank's Tuesday project- a short stay/high bb/slack head angle 29'r woods bike
Segmented to fit 16" stays on a 29'r

I can't believe he built this thing in one work day.

(p.s.- he wants to sell it)

JJ is a 17 year old Indiana based xc ripper who is about to receive his first factory bike.


This weeks 29'r output(I just dropped 4 more tube sets off at the shop a few hours ago)


2 of a batch of 10.

[Jeff Buchanan]

R.S. " Rene Singer" stainless lugset and crown...just like the man says...just trying to get in touch with my inner constructeur.